How to Choose Epoxy Flooring Companies Near Me: Questions DFW Homeowners Should Ask
Coating your garage, patio, basement or commercial space is a worthwhile upgrade in Dallas–Fort Worth. But searching “epoxy flooring companies near me” returns endless options, and in North Texas the wrong contractor shows up fast: extreme heat, shifting clay soils and heavy vehicle traffic mean poor prep or low-grade materials cause peeling, hot-tire pickup and bubbling within months.
At Apex Floor System we believe every property owner deserves full transparency. This guide covers what to verify and which questions to ask, using the standards we apply on every project in Plano, Frisco, McKinney, Allen and across DFW. If you are still comparing DIY options, start with our guide to garage floor paint options.
The Essential Contractor Checklist
Before you compare prices, confirm these three basics with every company on your list.
Licensing and insurance
Ask for General Liability and Workers’ Compensation coverage, which protects your property and the crew. Apex carries both.
In-house crew vs. subcontractors
In-house crews give consistent quality control. Apex never outsources to third-party subcontractors.
Industrial equipment
Look for commercial planetary diamond grinders with HEPA dust containment so dust is not blown into your home.
4 Questions to Ask Any Epoxy Flooring Contractor
The answers to these four questions tell you more about a contractor than any quote.
“What surface preparation method do you use?”
Look for: heavy-duty diamond grinding. Apex grinds every slab to a CSP-2 to CSP-3 profile so coatings lock in permanently.
“Do you test for moisture vapor emissions?”
Look for: calibrated electronic moisture testing before installation. When readings are elevated, Apex installs a moisture vapor barrier primer.
“What products will you apply, and what is the total dry film thickness?”
Look for: 100% solids epoxies and polyaspartics with a 10–20+ mil build.
“How do you handle cracks, spalls and joints?”
Look for: repair with polyurea joint and crack fillers before the basecoat. Coating over unaddressed cracks leads to telegraphing and surface breakdown.
Why Surface Preparation Decides How Long the Floor Lasts
Moisture vapor rising through porous concrete can create hydrostatic pressure that blisters topcoats, so testing before installation matters. The prep method matters just as much.
Acid etching or power washing
Neither opens the concrete deeply enough for long-term adhesion, and coatings applied over them tend to fail early.
Diamond grinding to CSP-2 to CSP-3
Mechanically opens the concrete pores so the coating locks in permanently, with HEPA vacuum containment to keep dust out of your home.
Film Thickness: Why DIY Kits Wear Through
Ask every contractor for the total dry film thickness. It is one of the clearest differences between a professional system and a store-bought kit.
How thick is the finished coating?
Dry film thickness in mils. Bars are drawn to scale.
DIY kits wear through under hot tires
Kits dry to just 2–3 mils, which is why hot-tire pickup is so common in North Texas garages. A 100% solids epoxy or polyaspartic system with a 10–20+ mil build is built to resist it.
Concrete Coating Systems Apex Offers
The right system depends on where the floor goes and how it is used. For a deeper comparison of the two main chemistries, read our guide to epoxy vs. polyaspartic garage floors.
| System | Best uses | Key benefits |
|---|---|---|
| Decorative flake / chip | Garages, patios, driveways, showrooms | Slip-resistant, masks concrete repairs, sealed with polyaspartic for UV resistance |
| Polyaspartic 1-day | Garages, outdoor patios, commercial | Rapid installation and quick return to parking; strong heat and chemical resistance |
| Metallic epoxy | Basements, living areas, retail, lobbies | Custom 3D marbled, high-gloss finish |
| Quartz broadcast | Commercial kitchens, wash bays, pool decks | Maximum slip resistance and impact durability |
| 100% solids epoxy | Interior storage, basements, warehouses | Economical, high-build, strong adhesion |
Timelines and Cost Expectations in DFW
2–3 days for multi-coat epoxy
Standard multi-coat epoxy systems typically take 2–3 days. Apex 1-Day Polyaspartic Flake Systems finish in 1–2 days, with foot traffic in 4–6 hours and vehicles back in 24–48 hours.
$3.00 to $10.00+ per square foot
Professional installations in Dallas–Fort Worth vary with surface prep, materials and square footage. Insist on an itemized estimate so you can compare bids line by line.
Understand the Warranty
Ask for the warranty in writing and check what it covers. Apex backs every installation with a written warranty of up to two years against peeling, hot-tire pickup and adhesion failure. Vague verbal promises from out-of-town franchises are a red flag.
Red Flags When Hiring a Flooring Contractor
- Acid etching or pressure washing as the only prep
- No moisture testing
- No mention of film thickness or product solids
- No written, itemized quote or warranty
- Work subcontracted to unknown crews
Why DFW Property Owners Trust Apex Floor System
Apex specializes in concrete coatings engineered for North Texas, combining industrial diamond grinding with top-tier material chemistry and local customer support for homes and businesses in Plano, Frisco, McKinney, Allen and the surrounding metroplex. Pick your city to see local details.
Frequently Asked Questions
How do I choose an epoxy flooring company near me?
Verify licensing and insurance, confirm an in-house crew, and ask about diamond-grinding prep, moisture testing, product solids and film thickness, crack repair, and a written warranty.
Why is diamond grinding better than acid etching?
Diamond grinding mechanically opens concrete pores to a CSP-2 to CSP-3 profile for permanent adhesion. Acid etching or washing is generally not sufficient for long-term bond.
What should an epoxy flooring quote include?
An itemized, per-square-foot breakdown covering prep, repairs, materials, system type and warranty terms, with no hidden fees.
How much does epoxy flooring cost in Dallas–Fort Worth?
Typically $3.00 to $10.00+ per square foot depending on prep needs, material selection and project size.
How long does an epoxy or polyaspartic floor installation take?
Standard multi-coat epoxy takes about 2–3 days. A 1-day polyaspartic flake system takes 1–2 days, with foot traffic in 4–6 hours and vehicles in 24–48 hours.
Ready to hire an epoxy flooring company you can trust?
Apex offers free on-site inspections across Plano, Frisco, McKinney, Allen and greater DFW, with per-square-foot pricing and an itemized quote.
- Free On-Site Estimate
- Up to 2-Year Written Warranty
- Locally Owned
- Licensed & Insured